CZ115 / CW722R Extruded High Tensile Brass (Restricted Al), CZ115 (CW722R) Brass Alloy, Extrudtion brass, excellent strength Brass extrusions, CuZn40Mn1Pb1FeSn brass roll coil sheet, Yellow Brass China Factory CZ115 / CW722R Extruded High Tensile Brass (Restricted Al) consists of of a duplex structure and is a high tensile brass with a restricted aluminium content, enabling […]
Naval Brass Round Rod, International Standards Brass Rods, Brass Sections and Profiles, ADMIRALITY BRASS TUBES, Forging Brass Naval Bars and Rods, ASTM Standard Specification for Brass Rod Bar Shapes, brass rod (round, hexagonal, and octagonal), bar (rectangular and square)
Naval Brass Round Rod – These high-quality brass rods are manufactured as per various national and international standards like :
Free Cutting Brass Rods
IS 319/89 – Grade I
IS 319/89 – Grade II
IS 319/89 – Grade III
BS 2874 – CZ 121 Pb3
BS 2874 – CZ 131
CW 614 N EN 12164 : 1998
Forging Brass Rods
IS – 6912/2005 FLB
Modified Forging Brass Rods as per IS – 8737
CW 617 N EN 12164 : 1998
High Tensile Brass Rods
HT-1 is suitable for soldering.
HT-2 is suitable for machining.
BS 2874 – CZ 114
BS 2874 – CZ 115
Naval Brass Rods
IS 291/89 – Grade I
IS 291/89 – Grade II
CDA 464 and CDA 385
Lead Free Brass
70:30 Lead Free Brass and
65:35 Lead Free Brass Rods.
Round Shaped Rods are produced in the following dimensions:
Drawn Rods and Bars – 5.00mm to 63.50mm
Extruded Rods and Bars – 15.00mm to 127.00mm
Available Straightened – 15.00mm to 80.00mm
Standard Length – 2.5m to 5.0m
This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, and C27400. The material shall be made from cast billets, logs, or rods of copper alloy, as determined by chemical analysis. The products shall be manufactured by such hot working, cold working, and annealing processing as to produce a uniform wrought structure. The material shall conform to the chemical compositional requirements prescribed for copper, lead, iron, and zinc. The standard tempers, either hard or soft anneal (namely: O60, H01, H02, and H04), for rod and bar are specified. Tensile requirements to which the product shall conform includes tensile strength, yield strength, and elongation. The dimensional requirements for rods, bars, and shapes are given. High Tensile Brass Hollow Pipes Brass Lead Free Hollow Rods
1.1 This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, C27400, C27450, C27451, C27453, and C28500. International Standards Brass Rods
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.